Water filtration

Backwashing Filters vs Cartridge Filters for Borehole Water

By the WaterQuotes team · Published 2026-11-16 · 5 min read

Side-by-side flat illustration of a backwashing media filter vessel and a cartridge filter housing for borehole water

If your borehole water is clean and clear, almost any filter will do. But most South African boreholes are not clean and clear — they carry iron, manganese, fine sand, sediment, or all four. Choosing the wrong filter type means either clogging a cartridge every few days or buying a backwashing system that is larger than you need. This article compares the two technologies honestly so you can go into the quote process knowing what to ask for.

How each technology works

A cartridge filter is straightforward: water passes through a pleated or wound polypropylene element inside a housing. When the element is dirty, you unscrew the housing, discard or rinse the cartridge, and replace it. Housings range from a single 10-inch unit to a multi-stage bank.

A backwashing filter uses a tank filled with a filter media bed — typically sand, crushed glass, birm, greensand, or catalytic carbon depending on what it is treating. During normal operation, water flows down through the bed and contaminants are trapped. On a timed or pressure-differential trigger, the control valve reverses flow, flushing the trapped material to drain. The bed is then ready to filter again, usually within ten minutes. No cartridge is thrown away.

Which contaminants each type handles well

ContaminantCartridge filterBackwashing filter
Fine sediment (low levels)GoodGood
Fine sediment (high levels)Clogs rapidlyGood — high capacity
Iron (dissolved, <0.3 mg/L)Adequate with carbon blockMarginal
Iron (dissolved, >0.3 mg/L)Clogs quicklyGood — birm or greensand media
ManganesePoorGood — greensand or catalytic media
HardnessPoorGood — if cation resin used
Biological riskInadequate aloneInadequate alone — always pair with UV or chlorination

The table shows a pattern: cartridges are fine for light polishing; backwashing vessels suit heavy or dissolved loads. Neither technology, on its own, renders borehole water safe to drink under SANS 241 (2024 edition) — you will still need a disinfection stage. For a broader look at complete treatment trains, the water filtration guide covers how stages stack together.

Running costs — the number that changes the decision

This is where many homeowners are surprised. A cartridge housing may cost a few hundred rand; the vessel for a backwashing system typically runs considerably more upfront. But the ongoing picture reverses.

On iron-rich or sandy borehole water, a 20-micron sediment cartridge in a single housing can need replacement every one to four weeks. Even at modest cartridge prices, that adds up to a significant annual spend — and the labour of changing them regularly. A backwashing system uses municipal or tank water for each backwash cycle, which is a real but comparatively small ongoing cost.

The full breakdown of filtration running costs works through the maths in detail, but the short version is: on dirty water, backwashing systems typically reach cost parity with cartridges within two to three years, then run cheaper indefinitely. On lightly loaded water the crossover may never come, making cartridges the sensible choice.

Space, power and installation requirements

Cartridge housings are compact. A bank of three housings — pre-sediment, iron-removal block, and final polish — fits on a bracket on a wall and needs no electricity beyond a downstream pump.

A backwashing vessel is larger: a typical residential unit for a family of four is roughly 250–300 mm in diameter and 1.5 m tall, plus the control valve head. It needs a power supply for the timer valve (a standard 220 V socket is usually sufficient) and a drain line to discharge backwash water. If you are on a septic system, confirm with the installer that the backwash volume will not overload it.

Backwashing systems also need a minimum flow rate to fluidise the media bed properly during the backwash cycle. If your borehole pump and rising main cannot sustain that flow rate, the bed will not clean itself effectively. This is a key detail to raise when requesting quotes — your borehole’s yield and pump curve matter.

Not sure which filter type your borehole water actually needs? Get three free installer quotes — vetted local professionals, no obligation.

Maintenance reality check

Backwashing filters are often described as ‘self-cleaning’, which is mostly true — but not completely. You should expect to:

  • Check and clean the control valve strainer basket every six to twelve months
  • Replace the filter media every five to ten years depending on the water chemistry (iron media exhausts; sand compacts)
  • Test your water annually to confirm the system is still performing — a borehole-specific filtration check is a good starting point for understanding what parameters to track

Cartridge systems require more frequent physical intervention but are simpler to service yourself. If you travel regularly or cannot commit to a maintenance schedule, a backwashing system with a reliable control valve is the lower-risk choice.

Upfront cost — what to budget

As a Johannesburg reference point, complete borehole systems including filtration typically run R40,000–R150,000 installed, with most falling between R60,000 and R100,000. Filtration alone — separate from the pump and casing — is a subset of that figure. A multi-stage cartridge bank might add R3,000–R8,000 installed; a backwashing media vessel with control head and installation could typically range from R8,000 to R25,000 or more depending on tank size and media type. Treat those as rough guides and confirm actual costs through quotes, because media choice, local labour rates and your specific water chemistry all shift the number materially.

Outside Johannesburg, treat any price above strictly as a reference point; regional pricing varies.

Ready to see what local installers would actually charge for your setup? Compare up to three free quotes — no commitment required.

Which to choose — a simple decision framework

Start with a water test, not a product. If you do not know your iron, manganese, pH, turbidity and total dissolved solids levels, any recommendation is a guess. Once you have the numbers:

  • Light sediment, low iron (< 0.3 mg/L), occasional use: a cartridge system is likely sufficient and cheaper overall.
  • High sediment, iron above 0.3 mg/L, or manganese present: a backwashing vessel with the right media will serve you better and cost less over time.
  • Both: a backwashing vessel upstream followed by a final cartridge polish is a common and effective combination.
  • Biological risk: add UV disinfection or chemical dosing regardless of which mechanical filter you choose.

When you request quotes, ask each installer to justify their recommendation against your actual test results. A good installer will specify media type, backwash flow requirements, and expected cartridge or media replacement intervals in writing. That is the information you need to compare proposals honestly.

Quick answers

Can I use a cartridge filter on high-iron borehole water?

You can, but it is usually impractical. Dissolved iron oxidises on the cartridge surface and clogs it rapidly — sometimes within days on water with iron above 0.5 mg/L. You would be replacing cartridges so frequently that the running cost becomes unacceptable. A backwashing system with birm or greensand media is a far better fit for elevated iron levels.

How much water does a backwashing filter waste per cycle?

It varies with tank diameter and media type, but a typical residential backwashing vessel uses roughly 100–300 litres per backwash cycle. Cycles usually run once every one to three days depending on your water quality and usage. If you are on a borehole with limited yield, factor this into your daily water budget and ask the installer to programme the least-frequent cycle that still keeps the bed clean.

Do backwashing filters need electricity?

The control valve timer does need a power supply — typically a standard 220 V socket. The filter itself is passive; water pressure does the work. If you experience frequent load shedding, ask the installer whether the control valve has a battery backup or whether manual backwash is possible, so a power outage does not leave the bed saturated with trapped contaminants for days.

How often does the filter media in a backwashing vessel need replacing?

Sand and crushed glass media can last ten years or more in moderate conditions. Iron-removal media such as birm or greensand exhausts faster — typically five to eight years — especially in high-iron water. Catalytic carbon for chlorine or hydrogen sulphide usually needs replacement every three to five years. Your annual water test will show if performance is declining before the media is completely spent.

Is a water test really necessary before choosing a filter?

Yes, and it is the step most homeowners skip. Choosing media or cartridge rating without knowing your actual contaminant levels is guesswork that can result in an undersized system, the wrong media, or a filter that does nothing useful for your specific water. A basic borehole water test covering turbidity, iron, manganese, pH, hardness and total coliform is the minimum starting point, and it is relatively inexpensive compared to buying the wrong equipment.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: Water Research Commission

Ready to compare? Get up to 3 quotes from vetted water filtration installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes