How it works

Protecting a Borehole Pump from Dry Running, Power Surges and Lightning

By the WaterQuotes team · Published 2026-11-19 · 7 min read

Flat illustration showing a submersible borehole pump with protection devices: dry-run switch, surge arrestor and voltage relay on a control panel

A submersible pump sits in darkness, often 60–100 metres underground, doing its job silently — until it doesn’t. When it fails, the culprit is almost always one of three things: it ran dry, the voltage spiked, or lightning found a path down the cable. Each cause is preventable. Each protection device costs a fraction of a replacement pump. This article explains what the devices are, how they work, and what a properly specified installation should include.

Why Submersible Pumps Are Vulnerable

Submersible pumps are cooled by the water flowing around them. Stop the water flow — whether because the water table drops, the borehole yield is lower than expected, or a check valve fails — and the motor overheats within minutes. That is a dry-run event, and it is one of the most common causes of premature pump failure in South Africa.

Add to that the reality of the Eskom grid: voltage fluctuations, sudden outages and reconnections all stress motor windings. Then consider the Highveld storm season: a lightning strike does not need to hit the borehole directly. A nearby strike induces a voltage surge through the power cable or the casing and into the motor — with the same destructive result.

Because the pump is underground and not visible, damage often goes undetected until the pump stops delivering water entirely. By then, the motor windings are burnt or the impeller is seized. Pulling and replacing a submersible pump is a significant cost on top of the hardware. For context, borehole pump costs typically run R15,000–R35,000 installed in Johannesburg; nationally the figure varies, so treat that as a reference point and confirm with local quotes.

Dry-Run Protection: The Non-Negotiable First Layer

Dry-run protection cuts power to the pump when it detects that water is no longer flowing or that the water level has dropped below a safe draw-down point. There are two main approaches:

Flow switches detect whether water is actually moving through the pipework after the pump. If flow drops to near zero while the pump is running, the switch trips the circuit.

Float or electrode level switches are mounted in the borehole casing at a set depth. When the water level drops to that point, the switch signals the control panel to shut the pump off. The pump restarts automatically — typically after a preset delay — once the level recovers.

A quality installation will include one or both of these, matched to the borehole’s tested yield. The yield test, conducted before the pump is sized, determines how hard the pump can be run without over-drawing the aquifer. If a pump is sized too aggressively for the yield, no protection device fully compensates — sizing and protection work together.

Note that a motor thermal overload relay in the control panel provides a last line of defence against overheating, but it reacts to symptoms rather than preventing the cause. It is not a substitute for a dedicated dry-run cut-off.

Voltage and Phase Protection

The South African grid delivers power that is nominally 230 V single-phase or 400 V three-phase, but supply quality varies. Submersible pump motors — particularly three-phase models — are sensitive to:

  • Under-voltage and over-voltage: Both damage windings over time. Under-voltage causes the motor to draw higher current to maintain torque, generating heat.
  • Phase loss or imbalance (three-phase systems): If one of the three phases is lost or significantly weaker, the motor runs on reduced phases, overheats rapidly and fails.
  • Rapid reconnection after outages: When grid power returns after load-shedding, the reconnection can produce a voltage transient that stresses motor insulation.

A voltage protection relay (also called an over/under-voltage relay or motor protection relay) monitors supply voltage continuously and disconnects the pump if voltage strays outside a set band. For three-phase systems, a phase-failure relay adds protection against phase loss and imbalance. These devices are compact, fit inside the control panel, and are significantly cheaper than a pump motor.

The electrical installation must comply with SANS 10142 (the South African wiring code) and all work should be done by a registered electrician. The Department of Employment and Labour’s Occupational Health and Safety Act regulations apply to electrical installations; always obtain a Certificate of Compliance for any new electrical work. If you want to understand typical costs for this side of the job, the borehole electrical connection cost breakdown is worth reading before you request quotes.

Sizing protection devices correctly starts with the right installer. Compare 3 free quotes — vetted installers, no obligation.

Lightning and Surge Protection

The Highveld — Gauteng, Mpumalanga, Limpopo and parts of the North West — experiences some of the highest lightning ground-flash densities in the world during the summer storm season. Even coastal and Western Cape boreholes face occasional surge risk from grid-borne transients.

Protection operates at two levels:

Surge arrestors at the control panel clamp transient voltages that arrive via the power supply. They are sacrificial devices: they absorb the surge energy and may need replacement after a significant event. They should be rated appropriately for the supply voltage and replaced after any confirmed surge event rather than assumed still functional.

Cable and earthing practices are equally important. The pump cable should be properly clamped inside the casing to prevent it acting as an antenna. The control panel earth must be sound. Some installers add a spark gap or additional lightning arrestor directly at the pump cable terminals. Where the borehole is in an area with very high lightning frequency, a lightning protection specialist may recommend additional measures for the surface installation.

One point often missed: if a nearby strike induces a surge and the pump fails shortly afterwards, standard home insurance may not cover the pump without a specific endorsement. It is worth reviewing your policy before an event rather than after. The guide on borehole insurance cover sets out what to look for in a policy.

The Control Panel: Where All Protection Comes Together

All the protection devices above are wired into or controlled via the pump’s control panel (sometimes called a starter panel or pump controller). A basic panel for a single-phase pump might contain only a contactor and overload relay. A properly specified panel for South African conditions should include:

DeviceWhat it guards against
Dry-run / level switchWater table drop, low-yield over-pumping
Flow switchBlocked suction, pipe failure, check-valve fault
Over/under-voltage relayGrid voltage fluctuations
Phase-failure relay (3-phase)Phase loss, phase imbalance
Surge arrestorLightning-induced and grid transients
Motor thermal overloadSustained overheating (last resort)
Time-delay relayPrevents rapid restart after shutdown

The time-delay relay is a small but important addition: it prevents the pump from immediately restarting after a dry-run shutdown, giving the water level time to recover. Without it, a pump can short-cycle — repeatedly tripping and restarting — which stresses the motor even when no dry-run occurs.

Panel specification should be part of the quote conversation, not an afterthought. Ask each installer explicitly what protection devices are included and what is optional. If a quote omits the protection layer entirely, that is relevant information about the quality of the installation being offered.

Protection specifications vary significantly between installers — getting multiple quotes makes the differences visible. Get your free installer comparisons — no obligation, no pressure.

Maintenance: Protection Devices Need Checking Too

Protection devices are not fit-and-forget. A float switch can corrode or jam in the open position, giving a false signal that the borehole is full when it is not. A surge arrestor that absorbed a strike may show no visible damage but be unable to protect against the next event. Voltage relays can drift in their set points over time.

As a practical routine:

  • Annually, have the control panel inspected by a qualified electrician. Check set points on voltage relays, test the dry-run cut-off manually if the design allows it, and inspect surge arrestors for the indicator flags many models include.
  • After any significant lightning event in the area, treat surge arrestors as potentially spent and have them checked.
  • If the pump trips repeatedly, do not simply reset it and hope for the best. Repeated tripping is diagnostic information. The article on borehole pump tripping causes and fixes walks through the common causes — some are protection devices doing their job correctly, some indicate a developing pump fault.

Water quality is a separate but related concern: even a mechanically sound pump delivering water from a borehole cannot guarantee potable supply without testing. SANS 241 (2024 edition) is the South African drinking-water quality standard; any borehole intended for drinking water should be tested against it by an accredited laboratory, and treated if required. The principle here is straightforward: test first, treat second.

What to Ask an Installer Before You Sign

When you receive quotes for a borehole installation or pump replacement, ask each installer to confirm in writing:

  1. What dry-run protection is included, and how is it set relative to the tested yield?
  2. Is a voltage protection relay (and phase-failure relay if three-phase) included in the panel?
  3. What surge protection is specified, and to what rating?
  4. Who does the electrical work, and will a Certificate of Compliance be issued?
  5. What is the warranty on the pump motor, and does the manufacturer’s warranty require specific protection devices to be fitted?

That last point matters: some pump manufacturers specify that their warranty is void if the pump is installed without dry-run protection. Checking the datasheet before installation costs nothing; finding out afterwards costs significantly more.

Quick answers

What is dry-run protection on a borehole pump?

Dry-run protection is a device or combination of devices that cut power to the pump motor when it detects that water is no longer flowing or the water level has dropped too low. Without it, the pump motor — which relies on surrounding water for cooling — overheats and can burn out within minutes of running dry. It is typically implemented as a float or electrode level switch in the casing, a flow switch on the discharge pipe, or both.

Do I need lightning protection if my borehole is not in a high-lightning area?

Surge protection is advisable regardless of location because lightning does not need to strike the borehole directly — grid-borne transients from strikes elsewhere on the network can travel down the power cable and damage the motor. That said, the level of protection can be matched to local risk: Highveld installations face higher frequency events and may warrant more robust arrestors and earthing. Discuss local risk with your installer and ask what surge protection is included in the quote.

Will my home insurance cover a borehole pump damaged by lightning?

Standard home insurance policies vary significantly in how they treat borehole pumps — some exclude them entirely as 'below-ground plant', others cover them only with a specific endorsement or if lightning damage to other fixed equipment is covered. Review your policy wording before an event and confirm whether the pump and control panel are listed as covered items. The guide on borehole insurance cover on this site sets out the key questions to ask your insurer.

How often should borehole pump protection devices be serviced?

An annual inspection by a qualified electrician is a sensible minimum, covering control panel condition, voltage relay set points, dry-run switch operation and the status of surge arrestors. After any significant nearby lightning event, surge arrestors should be inspected and replaced if indicated — many models have a visible flag or indicator that shows whether the device has been spent. Skipping maintenance increases the risk that a protection device fails silently and offers no protection when it is needed.

Can I add protection devices to an existing borehole installation that lacks them?

Yes, in most cases protection devices can be retrofitted to an existing control panel or a new panel can be installed alongside an existing one. The scope depends on what is already in place and the pump's electrical specification. This work must be done by a registered electrician, and a Certificate of Compliance should be issued for any changes to the electrical installation. Getting two or three quotes for the retrofit is worthwhile, as panel specifications and pricing vary between installers.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: Department of Employment and Labour · Eskom

Ready to compare? Get up to 3 quotes from vetted borehole drilling installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes