How it works
Types of Borehole Pumps: Submersible, Helical Rotor, Surface and Solar Compared
By the WaterQuotes team · Published 2026-10-30 · 6 min read
Choosing the wrong pump for a borehole is one of the most common and most expensive mistakes South African homeowners make. The pump type affects running costs, maintenance frequency, longevity, and whether the borehole will actually deliver enough water when you need it. Before you sign anything, it helps to understand what each category does, where it excels, and where it falls short.
This guide covers the four pump types you’ll encounter when talking to installers about a borehole system: submersible, helical rotor (also called progressive cavity), surface centrifugal, and solar-powered configurations. Solar is less a pump technology and more a power-delivery choice, but it changes your options enough to warrant its own section.
Submersible Pumps: The Workhorse Choice
Submersible pumps sit inside the borehole casing, fully below the water level. The motor is sealed and cooled by the surrounding water, and the pump pushes water up to the surface rather than pulling it — which is why depth is far less of a limitation than with surface pumps.
Where they work well: Boreholes deeper than about 7–8 metres, which covers the majority of productive residential boreholes in South Africa. They handle a wide range of yields and can be sized from small domestic units right up to commercial-scale installations.
Typical trade-offs: Because the motor is underground, servicing requires pulling the entire pump assembly — this usually means hiring a specialist with the right lifting equipment. A pump installed too deep in a low-yield borehole can also run dry and burn out within months if a float switch or pump controller isn’t fitted correctly.
For residential use, submersible pumps are often the installer’s default recommendation. If you want to understand how to choose the right size before quotes arrive, the key variables are the borehole’s rest level, pumping level, and tested yield in litres per hour — not guesswork.
Helical Rotor Pumps: Built for Low-Yield Boreholes
Helical rotor pumps (sometimes called progressive cavity pumps) use a spiralling rotor inside a stator to move water upward in a steady, low-turbulence flow. They are slower and gentler than centrifugal submersibles, which makes them well-suited to boreholes with modest yields.
Where they work well: Low-yield boreholes — typically those producing under roughly 500 litres per hour — where a conventional centrifugal submersible might empty the borehole faster than it recharges. Helical rotors are also tolerant of slightly sandy or turbid water, which matters in certain geological areas.
Typical trade-offs: They are generally slower to deliver water, so they work best paired with a storage tank rather than a direct-pressure system. They also have a rubber stator that degrades if the pump runs dry, so a reliable pump controller is non-negotiable. Installation and servicing costs are broadly similar to submersibles.
If your borehole test returns a low yield figure, ask your installer specifically whether a helical rotor is more appropriate than a standard centrifugal — this is not always volunteered upfront.
Surface Centrifugal Pumps: Simple but Shallow
Surface pumps sit at ground level and draw water up from the borehole. They are simpler to service — you can see and reach the motor without pulling anything from underground — and they are generally cheaper to purchase.
Where they work well: Shallow water tables, typically no more than 6–7 metres of suction lift. In practice, this limits them to a small subset of South African boreholes. They are more commonly seen in surface-water applications (dams, rivers) than in boreholes.
Typical trade-offs: Suction lift physics means these pumps struggle as the water table drops, which happens in most areas during dry seasons or prolonged drought. Priming can also be a recurring issue. For the majority of residential boreholes in greater Johannesburg and across the highveld, where water tables are typically much deeper than 7 metres, surface pumps are rarely the right answer.
If an installer recommends a surface pump for your borehole, ask for the logged depth-to-water measurement from the drilling report before agreeing.
Not sure which pump type your borehole needs? Compare 3 free installer quotes — vetted installers, no obligation.
Solar-Powered Configurations: An Energy Layer, Not a Pump Type
Solar borehole pumps are not a distinct pump technology — they are submersible or helical rotor pumps paired with solar panels and a pump controller or inverter instead of mains power. The distinction matters because you’re choosing both a pump type and a power source.
Where they work well: Properties with unreliable grid power, high electricity costs, or remote locations where running a mains cable is impractical. In a South African context, load-shedding has made solar configurations increasingly attractive even for urban homes. The details of how these systems are sized and costed for Johannesburg conditions are worth reading separately — solar-powered boreholes in Johannesburg covers the practical decisions involved.
Typical trade-offs: Solar configurations cost more upfront than a mains-connected pump of equivalent capacity. Pumping rate may vary with cloud cover unless a battery buffer or storage tank is sized into the system. A well-designed solar borehole system pumps during daylight into a storage tank, so the household draws from storage around the clock — this tank sizing is critical and often undersized by inexperienced installers.
As a Johannesburg reference point, borehole pump installations (excluding the full drilling and casing) typically run R15,000–R35,000 installed; solar configurations add to this depending on panel capacity and whether battery storage is included. For any other location, treat those figures as an orientation only and confirm via quotes.
How Installers Actually Choose Between Them
A competent installer will not recommend a pump type until they have — or you can supply — at minimum these three figures from a proper borehole test:
| Parameter | Why It Matters |
|---|---|
| Rest water level (metres below surface) | Determines whether surface pumps are viable at all |
| Pumping water level at test rate | Sets the required pump head and motor depth |
| Sustainable yield (litres/hour) | Governs whether you need a slow helical rotor or a faster centrifugal |
Without these, any pump recommendation is a guess. Installers who skip the test data and quote a pump immediately are a warning sign.
Pressure delivery is another layer on top of pump type — understanding the difference between constant-pressure and standard pump systems helps you brief your installer on what your household actually needs, rather than accepting a default configuration.
Ready to get real numbers for your property? Request up to three installer quotes — vetted installers, no obligation.
Questions to Ask Before You Sign
Once you understand the pump categories, the conversation with installers becomes more productive. A few questions worth raising:
- What yield and depth data is the pump recommendation based on?
- Is a pump controller or float switch included, and what does it protect against?
- What happens to servicing costs if the pump needs to be pulled — what equipment is required and what does that typically cost?
- If the borehole yield is marginal, is a helical rotor being considered?
- For solar configurations: is the storage tank sized to cover overnight demand, or just peak solar hours?
The right pump is the one matched to your borehole’s tested performance, your household’s daily demand, and your power supply situation. Getting three independent quotes is the most reliable way to stress-test a recommendation — different experienced installers looking at the same data will often agree on the core choice, and meaningful disagreement is itself useful information.
Quick answers
What is the most common type of borehole pump for residential use in South Africa?
Submersible pumps are the most widely installed type for residential boreholes in South Africa, mainly because most productive boreholes have water tables well below the 6–7 metre limit of surface pumps. They work at a wide range of depths and yields. Your installer should confirm the choice against your borehole's actual test data before specifying a unit.
When would a helical rotor pump be chosen over a standard submersible?
Helical rotor pumps are typically recommended for low-yield boreholes — broadly those producing less than around 500 litres per hour — where a centrifugal submersible could empty the borehole faster than it recovers. They move water more slowly and gently, and they tolerate slightly sandy water better than standard centrifugal units. The trade-off is that they generally need a storage tank rather than direct-pressure delivery.
Can I run a borehole pump on solar power during load-shedding?
Yes, solar-powered borehole configurations are designed to operate independently of the grid, making them resilient to load-shedding. The practical approach is to pump into a storage tank during daylight hours and draw from that tank around the clock. Sizing the tank and panels correctly is the critical step — undersized systems run dry overnight. A battery buffer can extend operation into the evening but adds cost.
How much does borehole pump installation typically cost in South Africa?
Using Johannesburg as a reference point, borehole pump installation (the pump itself, motor, pipework, and controller, but excluding drilling and casing) typically runs R15,000–R35,000. Solar configurations add further cost depending on panel capacity and storage. These are Johannesburg-specific figures; for other regions, treat them as a rough orientation and confirm actual costs through local installer quotes.
What borehole test data should an installer have before recommending a pump type?
At minimum, a responsible installer needs the borehole's rest water level, the pumping water level recorded during a yield test, and the sustainable yield in litres per hour. These three figures determine whether a surface pump is even viable, what motor depth and head are required, and whether a slow helical rotor is more appropriate than a centrifugal submersible. A pump recommendation made without this data is not well-founded.
Sources & notes
Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: Water Research Commission
Ready to compare? Get up to 3 quotes from vetted borehole drilling installers in Johannesburg — free, no obligation.
Get 3 free quotes