Installer selection guides

Common Water Tank Installation Mistakes and How to Spot Them

By the WaterQuotes team · Published 2026-11-10 · 6 min read

Flat illustration of a water tank on a cracked concrete base with warning symbols indicating common installation problems

A backup tank looks simple enough — a big plastic container, some pipe, a pump. But the gap between a tank that quietly does its job for fifteen years and one that causes grief within six months usually comes down to a handful of installation decisions most homeowners never think to check. This guide walks through the mistakes that show up most often, and what you can look for yourself before the installer packs up and leaves.

1. An Inadequate or Unlevel Base

This is the single most common structural mistake. A full 5,000-litre JoJo tank weighs roughly five tonnes. Put that on soft ground, uncompacted fill, or a slab that wasn’t sized for the load, and the tank will slowly shift or the base will crack. Once a large polyethylene tank sits at even a slight angle, the stress concentrates at the outlet fitting and the lower side of the tank wall — exactly where you don’t want it.

What to check: the base should be level in both directions (use a spirit level yourself if you’re unsure). Concrete slabs should extend at least 150 mm beyond the tank footprint on all sides. If the installer used loose bricks or compacted gravel without a concrete slab, ask why — that may be acceptable for smaller tanks but needs a clear justification for anything above 2,500 litres.

2. Undersized Inlet, Outlet, and Overflow Pipes

Pipe sizing is where a lot of rushed jobs go wrong. An inlet pipe that’s too narrow fills the tank slowly and creates back-pressure on your municipal supply. An outlet pipe that’s undersized starves the pump and reduces pressure to your taps. An overflow pipe that’s too small — or missing entirely — means that when the ball valve fails and the tank overfills, water has nowhere to go except over the lid or through joints that weren’t designed for that load.

As a rough guide, a standard residential tank system should have an overflow pipe at least as large as the inlet, discharged to a safe drainage point well away from the base. If your installer used 20 mm pipe where 25 mm or 32 mm is called for, that’s worth querying directly. Confirm the correct sizing for your specific pump and flow rate via quotes from at least two installers — the right answer depends on your setup.

3. No First-Flush Diverter on Rainwater Harvesting Systems

If your tank is fed by a rainwater collection system, the first water off a roof after dry weather carries dust, bird droppings, and other contaminants. A first-flush diverter diverts that initial flow away before clean water enters the tank. Without one, you’re accumulating contamination with every rain event.

This is a quick visual check: follow the downpipe from your roof to the tank inlet. There should be a vertical standpipe or dedicated diverter chamber before the water enters storage. If the downpipe feeds straight into the tank, it was left out. South Africa’s drinking-water quality standard, SANS 241 (2024 edition), sets the benchmark for potable water — rainwater used for drinking needs treatment and monitoring against that standard regardless of how good the collection system looks.

4. Missing or Incorrect Pump Protection

Dry-run protection is non-negotiable. When a tank empties and the pump keeps running against nothing, it overheats and fails — often within minutes. A pressure switch alone is not dry-run protection. You need either a low-water cut-off float switch wired to the pump, a dry-run protection relay, or a pump with built-in protection, depending on the system design.

Check the wiring and ask the installer to point out the dry-run protection device specifically. If they can’t, or if the only protection is a pressure switch on the outlet side, that’s a problem. For a broader look at what a properly specified system should include, the backup water systems guide covers the components in detail.

For more on what separates a careful installer from a careless one, the red flags to watch for when hiring a water installer is worth reading before you commit to anyone.

If you're not confident the quotes you've received address these issues properly, it costs nothing to check. Compare 3 free quotes — vetted installers, no obligation.

5. Poor or Missing Ventilation

Polyethylene tanks are not fully airtight by design — they need a vent to allow air in as water is drawn out, otherwise you get vacuum collapse, which can deform the tank permanently. The vent also needs a fine mesh cover to keep mosquitoes out. Standing water in a tank with open vents is a breeding ground for mosquito larvae.

Look for a screened vent fitting on the lid or upper wall. If the lid is simply left loose as a “vent”, that’s not good enough — debris, insects, and small animals can all get in.

6. Connections That Skip Isolation Valves

If there’s no isolation valve on the inlet, outlet, or both, you cannot service the pump, replace a fitting, or isolate the tank without draining the whole system. This sounds like a minor convenience issue until you need to replace a R15,000–R35,000 pump and discover there’s no way to do it without emptying 5,000 litres of water first.

Isolation valves should be accessible — not buried in a hole or tucked behind the tank where you need a contortionist to reach them. If they’re not there, ask the installer to add them before sign-off. This is exactly the kind of detail covered in what to expect when installing a backup water tank.

7. DIY Electrical Work on the Pump

Pump wiring that isn’t done by a registered electrician and covered by a Certificate of Compliance is both a safety risk and a problem when you try to claim on insurance after a fault. This applies whether the original installer did it or the homeowner tackled it afterwards. The question of when to handle installation yourself versus when to call a professional is a live one for many homeowners, but pump electrics sit firmly in the professional column.

Ask for the CoC before you make final payment. If the installer says it’s “not needed” for a small pump, that’s worth verifying with your municipality.

Getting the installation right from the start is far cheaper than fixing it later — a few minutes comparing installers can make all the difference. Get matched with vetted installers — free, no obligation.

How to Check Before You Sign Off

Before the installer leaves, run through this list yourself:

CheckWhat to look for
BaseLevel in both directions; concrete slab extends beyond tank footprint
Inlet / outlet / overflow pipesCorrect diameter; overflow discharged safely
First-flush diverterPresent on any rainwater-fed system
Dry-run protectionDedicated float switch or relay, not just a pressure switch
VentScreened; not just a loose lid
Isolation valvesAccessible on inlet and outlet
Electrical CoCIssued for any pump wiring

None of these checks require specialist knowledge. If you can’t get a straight answer to any of them, that’s information too.

Backup tank-and-pump systems typically run R20,000–R40,000 for straightforward setups, with whole-house configurations around R55,000 — these are Johannesburg reference points, so confirm local pricing through quotes. That’s a meaningful investment. A ten-minute walkthrough with the installer before they leave is a small insurance policy against finding out six months later that the base has shifted, the pump has seized, or the overflow has been silently flooding your foundation.

Quick answers

How do I know if my JoJo tank base is strong enough?

The base needs to be level in both directions and capable of bearing the full weight of a filled tank — a 5,000-litre tank weighs roughly five tonnes when full. A concrete slab is the standard solution for tanks of that size, extending at least 150 mm beyond the tank footprint on all sides. If you're unsure whether the existing base is adequate, ask a second installer to assess it before you commit to the current quote.

What is dry-run protection and why does my pump need it?

Dry-run protection cuts the pump off automatically when the tank empties, preventing the pump from running without water and burning out. A pressure switch on the outlet side is not the same thing — it responds to pressure in the pipes, not to the water level in the tank. You need a low-water float switch wired to the pump circuit, or a pump with built-in protection, to cover this properly.

Does rainwater stored in a JoJo tank meet the SANS 241 standard for drinking water?

Not automatically. SANS 241 (2024 edition) is the South African standard for drinking-water quality, and untreated rainwater typically won't meet it without filtration and disinfection. A first-flush diverter, appropriate filtration, and periodic testing are the minimum steps if you intend to use harvested rainwater for drinking or cooking. For garden irrigation or toilet flushing, the requirements are less stringent, but the tank and plumbing should still be clearly separated from the potable supply.

Can I wire up the pump myself to save money?

Pump wiring must be done by a registered electrician and covered by a Certificate of Compliance (CoC) — this is a legal requirement, not just a recommendation. Doing it yourself or accepting a job without a CoC creates a safety risk, may void your insurance, and can complicate things if you sell the property. The saving on the electrical portion of the job is rarely worth the exposure.

What should I do if I've already had a tank installed and I'm not sure it was done correctly?

Start with the visual checks in this article — base level, isolation valves, overflow pipe, screened vent, and dry-run protection. If you spot gaps, contact the original installer in writing and ask for the specific issues to be addressed before final payment if the job is recent. If the installer is unresponsive, getting an independent assessment from a second vetted installer is a reasonable next step. Document everything with photographs before anything is changed.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS

Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes