How it works

Rats, Frogs and Insects in Your Water Tank: Sealing Entry Points

By the WaterQuotes team · Published 2026-11-16 · 7 min read

Flat illustration showing a water tank cross-section with labelled entry points — lid, vent, overflow pipe — and icons of a rat, frog and mosquito being blocked by seals and mesh screens

A dead frog at the bottom of a tank is easy to overlook until someone notices the water smells wrong. By then the contents may have been circulating through taps for days. Animals enter storage tanks more easily than most homeowners realise, and the consequences range from unpleasant to genuinely hazardous. This guide explains how they get in, what the risk actually looks like, and the practical seals worth fitting before a problem starts.

How Animals Get Into a Tank in the First Place

Most entry points are designed into the tank — they just are not always sealed properly after installation.

The lid or manhole cover is the most obvious weakness. Plastic lids warp in UV exposure over a few years, leaving gaps wide enough for a rat to squeeze through. Some tank designs use lids that rest in a channel rather than locking down; without a rubber gasket or a weighted seal, they shift in wind or when the tank flexes during fill cycles.

Vents are necessary — a tank without ventilation develops negative pressure as water is drawn off, which can deform the walls or collapse cheaper polyethylene tanks. But an open vent pipe is an open door. Insects, small frogs and even juvenile rats can enter through a bare 20 mm or 25 mm vent opening. The same applies to any inspection port left without a cap.

Overflow pipes are frequently overlooked. An overflow that terminates in a straight horizontal or downward-facing open end invites animals to climb or crawl up from below. Rodents are capable swimmers and competent climbers; a pipe end resting near vegetation or ground level is accessible.

Inlet pipes that are not fitted with a floating-ball valve or a sealed entry point create a gap around the pipe where it passes through the tank wall — another entry route for insects in particular.

The result is that a tank technically purchased as “sealed” may have three or four functional gaps within a year of installation if no one checks the fittings.

The Health Risk When Something Dies in the Water

A decomposing animal in stored water introduces a range of potential contaminants: faecal bacteria, protozoa and, depending on the animal and the season, other pathogens. Frogs and rodents both carry organisms that can cause gastrointestinal illness in people who consume contaminated water.

Rodents specifically are associated with Leptospira bacteria — the cause of leptospirosis — which is shed in urine as well as through decomposition. The National Institute for Communicable Diseases (NICD) includes leptospirosis on its surveillance list as a disease of concern in South Africa, particularly in areas with high rodent populations.

Insects present a different but related risk. Mosquitoes breed in still water and can complete a life cycle inside an unsealed tank. Beyond the nuisance, Aedes and Culex mosquitoes are vectors for diseases monitored in South Africa. For more on how standing water and mosquito breeding interact, see the WaterQuotes article on mosquitoes and water tanks.

South African drinking water is assessed against SANS 241 (2024 edition), which sets microbiological and chemical limits for potable water. Tank water used for drinking or cooking should meet these limits — and the presence of a decomposing animal almost certainly means it does not until the tank is emptied, cleaned and retested. The principle to apply is straightforward: test first, treat second. Do not assume disinfection alone resolves the problem without confirming the tank is physically clean and the source of entry has been sealed.

Sealing the Lid

If your lid is the original factory-supplied plastic cap, check its condition annually. Look for warping, cracking around the rim and any gap when the lid is seated. Replacing a deteriorated lid is inexpensive compared to the alternative.

For round manhole lids, a closed-cell foam or EPDM rubber gasket fitted in the lid channel creates a compression seal when the lid is tightened or weighted. Some homeowners fit a simple locking mechanism — a stainless bolt and wing nut through the lid flange — which both seals the gap and deters deliberate tampering. The lid should be opaque; light encourages algae growth, which creates an additional hygiene problem.

Screening Vents and Overflow Pipes

Vents should terminate with a fine stainless-steel or brass mesh screen — typically 0.5 mm aperture or finer — fitted either inside the pipe end or over it with a jubilee clip. This allows airflow while blocking insects and small animals. Inspect the mesh at least twice a year because fine mesh blocks with dust and debris; a clogged vent can cause the pressure problems it was meant to prevent.

For overflow pipes, the standard fix is to:

  1. Extend the pipe so it terminates well clear of ground level and vegetation.
  2. Fit the end with a downward-facing elbow (a 180-degree return bend) so the opening faces the ground rather than outward or upward.
  3. Screen that opening with the same fine mesh.

This makes the pipe inhospitable to entry from below while still allowing water to discharge freely during overflow events.

If your tank setup needs a professional assessment alongside a new installation or upgrade, it costs nothing to compare options. Get 3 free installer quotes — vetted suppliers, no obligation.

Inlet Pipes and Wall Penetrations

Where a pipe passes through the tank wall, the gap around it should be sealed with a purpose-made tank fitting or a waterproof grommet rated for potable water contact. Silicone sealants are sometimes used, but they deteriorate and should not be your only seal. A properly sized threaded bulkhead fitting is the more durable solution and something a competent installer should supply as standard.

If your tank has a floating-ball valve on the inlet, confirm that the valve seat and surrounding area are intact. A valve that sits permanently open — either because it is stuck or because float adjustment is off — leaves the inlet path open.

Cleaning After an Animal Is Found

If you discover an animal in the tank, the water in the tank should not be used for drinking or cooking until remediation is complete. The process involves draining the tank fully, physical removal and disposal of the animal and any visible debris, scrubbing the interior, disinfection and then testing before resuming potable use. For a step-by-step guide to the cleaning process itself, see how to clean a water tank, and for advice on keeping stored water in good condition day-to-day, the guide on keeping stored water fresh covers rotation, light exclusion and other practical measures.

After cleaning, revisit every entry point described above before refilling. A tank that has had one intruder has, by definition, at least one unsealed gap.

Putting It Into a Maintenance Routine

Animal entry is a maintenance problem, not a one-off installation problem. Seals degrade, lids warp and mesh screens block or corrode. A practical annual check covers:

ItemWhat to checkAction if faulty
Lid and gasketWarping, cracks, gaps when seatedReplace gasket or lid
Vent screenMesh integrity, blockageClear or replace mesh
Overflow pipeTermination height and orientationReposition, add return bend and screen
Inlet fittingsGrommet or bulkhead seal conditionReplace fitting
Surrounding areaVegetation, debris near tank baseClear a 500 mm perimeter

Keeping vegetation cut back from the tank base reduces the access routes available to rodents and reduces the humidity that attracts frogs. It also makes visual inspection easier.

For a broader look at how tank-based backup systems work and what to consider when specifying one, the backup water systems guide covers system sizing, tank types and installation considerations in more detail.

Thinking about upgrading your tank setup with better-sealed fittings or a more secure enclosure? Compare quotes from up to 3 vetted installers — straightforward, no obligation.

When to Test the Water

Sealing alone does not confirm the water is currently safe. If there is any doubt about past contamination — an animal found, an extended period with an open lid, discoloured or malodorous water — arrange a water quality test against SANS 241 before resuming potable use. Accredited laboratories can test for microbiological parameters including E. coli, total coliforms and, if leptospirosis exposure is a specific concern, your healthcare provider can advise on appropriate testing. The Water Research Commission (WRC) publishes guidance on household water quality monitoring that may assist homeowners wanting to understand what a test covers and how to interpret results.

Quick answers

Is a frog in my water tank a serious health risk?

It can be. A live frog that leaves the tank without drowning may introduce bacteria or protozoa into the water, but the greater risk is a frog that dies and decomposes in the stored supply. If you find a dead animal in your tank, treat the water as potentially contaminated and do not use it for drinking or cooking until the tank has been cleaned and tested against SANS 241. The principle is test first, treat second.

How do I know if rats have been in my water tank?

Signs include a foul or unusual smell from the water, visible droppings around the tank lid or vent openings, gnaw marks on pipes or the lid itself, and in serious cases, a carcass at the bottom. Rodents are attracted to tanks that are near food sources, have accessible entry points and sit close to ground level. If you suspect rodent access, inspect every fitting and seal before the next fill cycle.

What mesh size should I use to screen a tank vent?

A mesh aperture of 0.5 mm or finer is typically recommended to exclude both insects and small animal entry while still allowing the airflow a tank needs to equalise pressure. Stainless steel or brass mesh holds up better in outdoor conditions than galvanised alternatives, which can corrode and block more quickly. Check the screen at least twice a year for blockage or damage.

Can I use the water from a tank where an animal was found, after I add bleach?

Disinfection alone is not a reliable fix after a carcass has been in the tank. The tank should be physically drained and scrubbed before any disinfection step, and the water should be tested before resuming potable use. Adding disinfectant to visibly or knowingly contaminated water without cleaning first is not considered adequate remediation under South African water quality practice.

My tank came sealed from the manufacturer — do I still need to check the entry points?

Yes. Plastic lids and gaskets degrade with UV exposure and temperature cycling over time, often within a few years. Vent and overflow fittings are sometimes left open or only loosely fitted during installation. An annual visual inspection of every penetration point — lid, vent, overflow, inlet — is worth building into your maintenance routine regardless of how the tank was supplied.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: NICD · Water Research Commission

Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes