How it works

Water Tank Leaking at a Fitting or Seam: Repair or Replace?

By the WaterQuotes team · Published 2026-11-10 · 6 min read

Flat illustration of a plastic water storage tank with a magnifying glass highlighting a leaking outlet fitting and a cracked seam

A dripping tank is easy to ignore — until you notice your stored water is half gone or a damp patch has appeared under the stand. Before you call anyone or buy anything, the most useful thing you can do is find exactly where the leak is coming from. The source determines whether you have a cheap afternoon fix or a tank-replacement decision.

Why Most Leaks Start at Fittings, Not the Wall

Polyethylene tanks — the rotomoulded type that dominates the South African market — are surprisingly resilient. The tank wall itself rarely fails unless the plastic has been physically damaged, exposed to incompatible chemicals, or degraded by prolonged UV exposure without adequate carbon-black content in the mix.

What does fail regularly is the junction between the plastic wall and any metal or plastic component threaded through it: outlet valves, inlet bulkhead fittings, float-valve ports and overflow connectors. Each of those penetrations is a potential leak point. The fitting compresses a rubber washer against the tank wall, and over time washers harden, fittings work loose from vibration or thermal cycling, or someone overtightened them and cracked the surrounding plastic.

This is good news in most cases: fitting leaks are far cheaper and simpler to address than structural ones.

How to Find the Exact Source

Do not guess. A leak that appears at the base of a tank could be dripping down from a fitting half a metre higher. Work through these steps before touching any tools:

  1. Dry the outside of the tank completely with a cloth and let it sit for ten minutes.
  2. Watch, not wipe. Stand back and observe where moisture first reappears. Mark it with a pencil or chalk.
  3. Check fittings first. Run a dry finger around every fitting, seam and outlet. The fitting that leaves your finger wet is the culprit.
  4. If the wall itself is wet, press lightly. A pinhole or hairline crack will show a slight bulge or wet spot under pressure.
  5. For underground or hard-to-access sections, fill the tank to its normal operating level overnight, mark the waterline, and check in the morning — a significant drop without visible external drips suggests an underground pipe joint, not the tank body.

Taking a photo of the leak location before draining the tank helps enormously if you later need to describe the problem to an installer or supplier.

Which Leaks Can Be Repaired

Loose or degraded fittings are the most repairable category. The process is straightforward: drain the tank to below the fitting, remove the fitting, replace the rubber washer (use a washer rated for potable water if the tank stores drinking water), apply PTFE thread tape and reassemble. Standard BSP (British Standard Pipe) fittings are widely available from irrigation, plumbing and agricultural suppliers across South Africa. For tanks used for drinking water, any materials in contact with the water should be safe for potable use — SANS 241 (2024 edition) governs drinking-water quality, and your fittings and sealants should not introduce contaminants.

Cracked plastic immediately around a fitting can sometimes be stabilised if the crack is small and the fitting itself can still compress a washer flush against undamaged material. Products sold as JoJo tank repair kits — typically a two-part epoxy or a plastic-compatible sealant with a backing patch — are designed for this purpose. They work best on cracks smaller than roughly 20–30 mm that are not under constant hydrostatic load. Drain the tank, clean and dry the area thoroughly, and follow the product’s curing time exactly before refilling.

Small impact holes in a sound wall can be patched the same way, though the patch will always be a weaker point. If the tank is more than ten years old, consider whether a patch is worth the effort.

For guidance on what to inspect regularly so small problems do not become large ones, our water tank maintenance checklist walks through the key checks by season.

When a Tank Must Be Replaced

Some conditions make repair uneconomic or unsafe:

  • A seam crack longer than a few centimetres. Rotomoulded tanks do not have traditional welded seams, but older tanks can develop stress fractures along the shoulder or base curve. A crack that runs along a structural curve will propagate.
  • Wall delamination or bubbling. This indicates internal degradation of the polyethylene, often from chemical incompatibility or extreme UV exposure. The material has lost structural integrity and no surface patch will hold reliably.
  • Multiple simultaneous leak points. If you repair one fitting and another starts weeping within weeks, the tank is telling you it is at end of life.
  • Visible distortion of the tank body. A tank that has been overfilled, undermined by poor base support, or exposed to excess heat may have warped. A distorted body changes the stress distribution on every fitting.
  • Unknown contamination history. If you acquire a second-hand tank and cannot verify what it stored, neither cleaning nor repair makes it suitable for potable water storage.

Understanding how different tank materials age helps you make this call. The guide to water tank materials covers polyethylene, fibreglass, steel and concrete options and their typical lifespans — worth reading before you decide whether repair or replacement gives you better value.

If a repair has not held or the tank is clearly at end of life, getting a few replacement quotes costs nothing. Compare 3 free quotes — vetted installers, no obligation.

Repair Costs vs Replacement Costs: a Rough Guide

A DIY fitting repair — new washer, PTFE tape, possibly a new brass or poly fitting — typically costs under R500 in materials. A repair kit for a cracked wall section runs roughly R200–R600 depending on the product, though that is a broad range and you should confirm current pricing with your local supplier.

Replacement tanks vary considerably by size and material. As a Johannesburg reference point, complete backup tank-and-pump systems typically run R20,000–R40,000, with whole-house setups around R55,000. The tank itself is only part of that — installation, pipework, a pump and any filtration account for a significant share. You can explore the full scope of what a backup system involves on our backup water systems pillar page.

ScenarioTypical actionRough material cost
Loose fitting, intact wallReplace washer, retightenUnder R200
Degraded fitting, minor crack around itFitting replacement + repair kitR300–R700
Wall crack under 30 mm, tank under 8 years oldRepair kit patchR200–R600
Seam crack, delamination, multiple failuresTank replacementQuote needed

These figures are for materials only. If you need a plumber or installer to do the work, add their call-out and labour. Always confirm pricing through actual quotes.

Warranties and What They Cover

Before you spend money repairing a tank, check whether it is still under warranty. Most major South African tank manufacturers offer a warranty on the tank body itself — typically against manufacturing defects in the polyethylene — but warranties rarely cover fittings, which are often sourced separately and installed by a plumber or the homeowner. Damage from incorrect installation, overfilling, unsupported bases or chemical contamination is almost universally excluded.

Keep your original purchase receipt and any installation documentation. If you are unsure what your warranty covers, our article on backup water warranties explains what to look for in the fine print and how to lodge a claim if you believe the fault is a manufacturing defect.

Deciding between a repair and a full replacement is easier with a professional's eyes on the tank. Get quotes from vetted installers — free, no commitment required.

A Practical Sequence Before You Decide

To summarise the decision process without overcomplicating it:

  1. Find the exact leak source — fitting, crack, seam or wall.
  2. If it is a fitting, attempt a repair yourself unless you are uncomfortable with basic plumbing.
  3. If it is a wall crack, assess the size, the tank’s age and whether it is isolated.
  4. If in any doubt about the structural integrity, or if the tank stores drinking water and the contamination risk is unclear, replacement is the safer call.
  5. Get at least two quotes for replacement before committing — both for the tank itself and for the installation, as these are often quoted separately.

A leak is rarely an emergency that forces a same-day decision. Taking an hour to diagnose it properly almost always saves money.

Quick answers

Can I repair a JoJo or similar polyethylene tank myself?

Yes, for fitting leaks and small wall cracks the repair is within most homeowners' ability. You will need to drain the tank to below the damaged area, dry the surface completely, and use a product specifically formulated for polyethylene — standard epoxy does not bond reliably to rotomoulded plastic. Follow the product's curing time before refilling, and do not apply a patch under water or in cold, damp conditions.

How do I know if a crack in my tank wall is serious?

Length, location and direction matter. A short crack — under about 20–30 mm — in a flat section of the wall, away from any structural curve or fitting, is a candidate for patching. A crack that follows a curve, runs along the base, or is growing is a sign of structural stress that a surface patch will not resolve. If the crack is longer than your palm or the plastic around it feels brittle, plan for replacement.

What sealant should I use on a tank that stores drinking water?

Use only materials rated safe for potable water contact. PTFE thread tape is generally acceptable for fitting threads. Two-part epoxy repair products should state on the packaging that they are food-safe or potable-water safe once cured. Avoid silicone sealants not rated for drinking water, and never use solvent-based products inside a tank that will store water for human consumption. SANS 241 (2024 edition) is the applicable South African standard for drinking-water quality.

My tank is leaking at the bottom outlet, but I cannot isolate the water supply to drain it. What can I do?

If the outlet has a ball valve downstream, close it and check whether the leak is from the fitting on the tank side or the valve itself — that narrows the problem without draining the tank. For the repair itself, you will need the water level below the fitting, so you will either need to pump the water to another container or temporarily run your supply from the mains while the tank drains naturally through use. Attempting to replace a fitting under hydrostatic pressure risks a larger failure.

Does a leaking tank affect my warranty?

It depends on the cause. A leak from a manufacturing defect in the tank wall — thin spots, blow holes, or material failure not caused by external damage — is typically covered. Leaks at fittings installed separately, damage from incorrect base support, overfilling, or chemical exposure are almost always excluded. Check your documentation for the specific exclusions, and read up on what backup water warranties typically cover before contacting the manufacturer.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS

Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes